EtherCAT DAQ Modules


EtherCAT DAQ Modules


MonoDAQ-E-ACC

  


          

 MonoDAQ-E-ACC 

 

  • Maximum Sampling Rate (1ks/s or 40ks/s) 
  • Isolated IEPE input
  • Dynamics: 90 dB SNR, 100 dB SFDR
  • 200 mV to 10 V input ranges
  • TEDS sensor support
  • EtherCAT interface



MonoDAQ-E-STG

 

 


          

 MonoDAQ-E-STG 

 


  • Maximum Sampling Rate (1ks/s or 40ks/s)
  • Fully isolated front end
  • Full, half, quarter bridge / 120, 350 ohm
  • Bipolar excitation 0 .. 12 V,
  • Unipolar excitation 0 .. 24 V
  • Shunt calibration, sensor balance
  • 100 mV to 50 V input ranges
  • Sensor power supply up to 400 mW
  • Current input 4-20 mA
  • TEDS support




MonoDAQ-E-gMeter

 

 


          

 MonoDAQ-E-gMeter 

 MonoDAQ-E-gMeter


A data acquisition device with embedded triaxial MEMS accelerometer, analog to digital conversion and EtherCAT interface based on the MonoDAQ EtherCAT platform.


Triaxial MEMS accelerometer with EtherCAT interface:
  • Extremely low noise: 25 ug/sqrt(Hz)
  • +-2 g, +-4 g, +-8 g measurement ranges
  • Signal and power in one cable
  • up to 50 m device-to-device





MonoDAQ-E-AO  

 

 


          

 MonoDAQ-E-AO   

 MonoDAQ-E-AO - low-latency analog output


Low Latency, high precision analog output module, with excellent dynamic performance. Under 100 microseconds of EtherCAT to analog delay achievable (on a real-time EtherCAT controller).


EtherCAT device with analog output:
  • High precision (0.1% +-1 mV)
  • Excellent dynamic performance (92dB SNR, -90 dB THD)
  • Low latency: under 100 us EtherCAT-to-analog delay (from real-time EtherCAT master)

MonoDAQ-E-DO4  

  


          

 MonoDAQ-E-DO4   

 MonoDAQ-E-DO4 - isolated, high current digital outputs

Isolated digital outputs with high current capability can drive motors, pumps or valves as well as trigger pure digital signals. Three power supply voltages (5V, 12V and device voltage supply level) available on the front connector. EtherCAT interface, signal and power over the same cable

EtherCAT device with 4 digital outputs:
  • Can drive motors, valves, pumps: open collector with max. 50 V / 2 A sink
  • Max. PWM switching frequency: 100 kHz
  • Front end power supply (5 V, 12 V, device supply voltage)
  • Galvanically isolated front end to ground

MonoDAQ-E-DI4

  


          

 MonoDAQ-E-DI4 

 MonoDAQ-E-DI4 - isolated digital inputs

Robust Isolated digital inputs are suitable for reading data of digital sensors, as well as for demanding test automation tasks. Three power supply voltages (5V, 12V and device voltage suplly level) are available on the front connector. EtherCAT interface, signal and power over the same cable.

EtherCAT device with 4 digital inputs:
  • Isolated inputs channel-to-ground and channel-to-channel
  • 20 kS/s sample rate to DEWESoft software
  • Front end power supply (5 V, 12 V, device supply voltage)


Contact us for Pricing!