USB DAQ Products


USB DAQ Products

MonoDAQ data acquisition product line


MonoDAQ-U-X

  • Analog voltage input & output
  • Current input
  • Thermocouple & RTD input
  • Digital I/O
  • Sensor excitation
  • Maximum Sampling Rate (1ks/s or 50ks/s) 

• configurable front end for any kind of sensors

• fully isolated USB (signal + power)

• 16 bit @50 kS/s @ ... 20 bit @100 S/s

• powerful DEWESoft software for PC

• cross-platform IDM software for embedded integrations





The same hardware can be reconfigured into a 1-channel strain gauge amplifier, 4-channel thermocouple interface or 8-channel voltage input with a single click of a button in DEWESoft data acquisition software. Analog and digital I/O’s coupled with Python API’s enable MonoDAQ-U-X USB Data Acquisition device (USB DAQ) to be used in basic control & automation applications. That is why our customers call it a true Data Acquisition (DAQ) Chameleon.



Data acquisition hardware

MonoDAQ-U-X is stackable to multiple devices that are synchronized over USB from the same hub. 8 multifunctional pins can be configured as analog or digital inputs or outputs. MonoDAQ-U-X is housed in a robust aluminium housing with a push-in front wire terminal. It also includes low-noise sensor excitation.



MonoDAQ-U-X general specifications

  • Power and signal isolation between USB and front end
  • Max. Sample rate 50kS/s or 1ks/s (16 bit), max. Resolution 20 bit (100S/s)
  • Can connect up to 2 full bridge strain gauges or up to 4 thermocouples
  • Max. 4 differential or 8 single ended voltage inputs
  • Current input with internal shunt (0.5 ohm)
  • Analog output (+/-4V, 14bit, 50kS/)
  • Max. 8 digital inputs or outputs
  • 1 wire, I2C and UART interface on front connector
  • Internal humidity sensor
  • Internal IMU (3-axial acceletometer and 3-axial gyroscope)

Data acquisition software

MonoDAQ-U-X product includes two software packages.


The ultimate Windows based data acquisition software, awarded by NASA Tech Briefs, comes along when purchasing the product.

DEWESoft X3 is known worldwide as a plug-and-play data acquisition software. Strong calculation backend brings it into the most demanding applications such as the space shuttle programme. Easy to use for everyone from students to rocket scientists due to its straightforward user interface.


IDM:  cross-platform Java package

Isotel DAQ & Metering (IDM) software is a Java based configuration and recording software package which runs on any platform supporting Java (Windows, Linux, Android, Mac etc.).

IDM is lightweight enough to run on Raspberry Pi or on Android smartphones. It can act as a backend gateway to Python API, making it easy to communicate with the MonoDAQ-U-X in Python. IDM can also be a remote gateway to DEWESoft X3.


Temperature Measurements


How to measure temperature?

Industrial temperature measurement is usually conducted in one of the two ways: with either a thermocouple or an RTD (resistance temperature detector). Both methods use the changing electrical properties of the sensing material with temperature to measure it.

How a thermocouple works?

A thermocouple is a pair of wires of different material that are joined at one end. At the other end there can be a small voltage measured between depending on the difference in temperature between the joint (hot junction) and the measurement point (cold junction). The relation between the voltage and temperature is non-linear and depends on the type of wire material. Different wire pairs form different type of thermocouples (K, T, J, E, R, S, T, C, B) and differ from each other in sensitivity and usable temperature range.

Thermocouples can measure temperature from almost absolute zero to more than 2000 degC, depending on the type.


What equipment is needed to measure temperature with thermocouples?


K-type thermocouple generates voltage of approximately 40 µV/degC, which means that 1 mV of measurement error would translate into 25 degC of temperature error. The measurement system therefore needs to have very good accuracy at low voltages. It also needs to have good protection from external disturbances such as 50 Hz noise from mains voltage or higher frequency electro-magnetic noise because even low voltages induced in measurement cables can translate in large temperature error. Measured voltage is linearized in software to compute the temperature, also taking into account the cold junction temperature.

A very important part of the measurement system is also the cold junction measurement. Cold junction is a point in the system where the thermocouple wires are joined with copper or gold (on the measurement device PCB or in the connector). The temperature at that point must be measured precisely since it is the reference for determining the absolute temperature at the hot junction.

How an RTD works?

RTD utilizes a change in resistance with temperature. The relation between temperature and resistance is non-linear, but not to the same extent as with thermocouples. Nominal resistance of an RTD at 0 degC determines its type: usually between 100 ohm (PT100) and 1000 ohm (PT1000). RTD’s are more accurate than thermocouples but also more expensive and can measure temperatures from -200 to 850 degC.

What equipment is needed to measure temperature with an RTD?

To measure resistance a precise current excitation is needed that generates a voltage drop accross the RTD. Low currents in the range of mA are needed in order not to overheat the RTD and cause measurement error due to self-heating. Voltage is then measured to determine the resistance and linearization is applied in software to calculate the temperature. No reference temperature is needed contrary to the thermocouples.


Contact us for Pricing!