EtherCAT DAQ Modules for Structural Health and MCM
EtherCAT DAQ Modules for Structural Health and MCM
MonoDAQ-E-ACC
Maximum Sampling Rate (1ks/s or 40ks/s)
Isolated IEPE input
Dynamics: 90 dB SNR, 100 dB SFDR
200 mV to 10 V input ranges
TEDS sensor support
EtherCAT interface
MonoDAQ-E-STG
Maximum Sampling Rate (1ks/s or 40ks/s)
Fully isolated front end
Full, half, quarter bridge / 120, 350 ohm
Bipolar excitation 0 .. 12 V,
Unipolar excitation 0 .. 24 V
Shunt calibration, sensor balance
100 mV to 50 V input ranges
Sensor power supply up to 400 mW
Current input 4-20 mA
TEDS support
MonoDAQ-E-ASI-2-T
MonoDAQ-E-ASI-2-T is a device with two analog sensor interface channels and one tacho channel. It converts the signal from MonoDAQ-SNS-ACC-1-10k-F sensors and sends the data over EtherCAT bus to the master PC. Up to two ACC-SNS sensors with M8 connectors can be connected.
Maximum Sampling Rate (40ks/s per sensor)
2 sensors predevice
EtherCAT bus
Daisy chain with single cable up to 50m
DEWESoft X3 software support
MonoDAQ-E-gMeter
MonoDAQ-E-gMeter
A data acquisition device with embedded triaxial MEMS accelerometer, analog to digital conversion and EtherCAT interface based on the MonoDAQ EtherCAT platform.
Triaxial MEMS accelerometer with EtherCAT interface:
Extremely low noise: 25 ug/sqrt(Hz)
+-2 g, +-4 g, +-8 g measurement ranges
Signal and power in one cable
up to 50 m device-to-device
MonoDAQ-E-AO
MonoDAQ-E-AO - low-latency analog output
Low Latency, high precision analog output module, with excellent dynamic performance. Under 100 microseconds of EtherCAT to analog delay achievable (on a real-time EtherCAT controller).
EtherCAT device with analog output:
High precision (0.1% +-1 mV)
Excellent dynamic performance (92dB SNR, -90 dB THD)
Low latency: under 100 us EtherCAT-to-analog delay (from real-time EtherCAT master)
MonoDAQ-E-DO4
MonoDAQ-E-DO4 - isolated, high current digital outputs
Isolated digital outputs with high current capability can drive motors, pumps or valves as well as trigger pure digital signals. Three power supply voltages (5V, 12V and device voltage supply level) available on the front connector. EtherCAT interface, signal and power over the same cable
EtherCAT device with 4 digital outputs:
Can drive motors, valves, pumps: open collector with max. 50 V / 2 A sink
Max. PWM switching frequency: 100 kHz
Front end power supply (5 V, 12 V, device supply voltage)
Galvanically isolated front end to ground
MonoDAQ-E-DI4
MonoDAQ-E-DI4 - isolated digital inputs
Robust Isolated digital inputs are suitable for reading data of digital sensors, as well as for demanding test automation tasks. Three power supply voltages (5V, 12V and device voltage suplly level) are available on the front connector. EtherCAT interface, signal and power over the same cable.
EtherCAT device with 4 digital inputs:
Isolated inputs channel-to-ground and channel-to-channel
20 kS/s sample rate to DEWESoft software
Front end power supply (5 V, 12 V, device supply voltage)